Double NGD: Charvel Model 5 and G&L Invader Plus

Well, I’ve done it again. While cruising the web, I found two guitars I just couldn’t pass up for their relative prices, so after some light talks with the sellers, both arrived at my home this Thursday.

First up, the Charvel Model 5. I originally purchased this mainly as a flipping opportunity, due to it’s great condition coupled with an irresistible price. Additionally, I’ve always wanted a neck-through guitar and a Charvel model 5, 550, 6, or 650 is right at the top of that list - with the added benefit of trying out some pickups I’ve never had before, the Jackson J80C. I did hope that the bridge pickup was a J90C or J95, but I wasn’t quite that lucky, both neck and bridge pickups are J80C’s.

The guitar interestingly has a 5-way switch despite having two pickups, and I just learned about this feature. It’s the Jackson JE-0005 “super switch.” Essentially, a standard 5-way switch has a few terminals and the way it switches sounds is by combining the outputs from each pickup in different ways, while this “super switch” has individual terminals for each possible switch position, so in theory you could wire it a multitude of ways impossible on a standard switch. There is a helpful write-up here on the JCF forum: https://www.jcfonline.com/threads/90074-Jackon-Special-5-Way-wiring-tutorial.

This guitar is stock, so the switch goes from neck (series humbucking), neck single coil, both pickups series (all four coils), bridge single coil, and bridge (series humbucking). It takes a little while to get used to it, but I think I prefer this arrangement more than the usual selector + coil tap mini switch. It’s certainly much quicker to use and requires a bit less fiddling when making quick transitions between humbucking and single coil sounds. This switch was also available on the Model 3A and 3DR of the same era, as well as the Predator later on.

It also comes equipped with a JE-1200 mid-boost circuit, which offers up to +6db of boost at around 650hz. On my Model 4’s and 475 Deluxe, I considered this boost an “always on” item that was required to avoid overly bright/shrill tones with the J50BC pickup. However, the J80C’s on this guitar have much thicker mids, and the boost is not as obvious - and certainly not required. That’s great, because I can leave it rolled off for rhythm or clean tones, then roll it up - though a clean amp I get a nice volume and edge-of-breakup sound, fantastic for soloing, and through a distorted amp I get just a little bit more saturation and push. This is a big advantage for me, as with the Model 4’s I’ve always felt like the mid boost feature was kind of worthless because it didn’t give me any extra options - it had to be on all the time. Next I need to get my hands on a J90 or J95 humbucker to try out, since those should have a little bit more output and thicker mids based on the specifications.

More details here: https://www.bretmcgonigle.com/guitars#/1986-charvel-model-5/

The G&L Invader Plus was a lucky acquisition, as I don’t usually look for guitars made past about 1990. I didn’t know much about this model, so I did a lot of digging and research on features, specifications, and values prior to purchasing. Everything came back looking like exactly my type of guitar, so I went for it. The quality of wood on this guitar is truly impeccable, and with quality hardware it’s truly an elite instrument. The figuring of the top is really nice, and a bit more interesting than some of the more common quilt or flame tops that look to me a bit too perfect. The grain gives a sensation of depth even though this top is not that thick, and the natural binding around the edges gives a nice separation between the cap and the mahogany body. The neck is really where it ramps up though, with some strong flame figuring on the player’s side of the neck that' is really nice to look at. The fretboard and neck is constructed entirely from a single piece, so the fretboard also possesses much of the same figuring. The flame is accompanied by a strong birds-eye figuring as well, so the neck really has a lot to appreciate.

I was hoping for a different bridge pickup (this has a Duncan JB, of which I have 7 or 8 at this point), but it sounds very thick and warm in this guitar so it’s hard to deny it’s a great sounding guitar. The JB can be a bit touchy depending on the guitar - for example, my ‘89 Pacer Custom I had a JB originally and it was so frustrating to have such a nice guitar sound so thin and harsh on almost all of my amps. The ‘59 is a neck pickup I’ve never had the chance to own before, so it’s nice to be able to play one of the bread and butter pickups so commonly discussed among guitar players. It has a great sparkle through a clean amp that none of my other guitars can quite match.

That said, the neck on this one is quite thick in comparison to my other guitars and I’m a bit surprised myself that I’m reaching for the Charvel above more than this instrument. Part of that is the G&L is in impeccable shape, with not even a visible scratch on it - it arrived with the original case, hang tags, certificate of authenticity, and even the plastic film still present over the plastic cavity covers. I’m almost afraid to play it for fear of marring its perfect form. Still, it has one of the most toneful clean sounds I’ve ever heard from an electric and I expect to be using it for those styles - perhaps this would be a good guitar to try some lower output pickups in (perhaps a Pearly Gates, or ‘59 Bridge?).

More details here: https://www.bretmcgonigle.com/guitars#/2002-gl-invader-plus/

A few Kramer guitar project updates

It’s been a while since the last update, but I’ve been traveling a lot for work and have had little time to work on my guitars. I was able to take a few evenings this week and I finally have completed one - and made a few changes to my others. The exciting news is that all three are fully playable - I may make a few minor changes moving forward, but I’m very happy to be playing them instead of staring at a pile of parts.

On the left, the transparent red Pacer C1 body from late 1989 - this body has some unique cutouts, despite sharing the 7/8 sharp-radius shape like the others. It has the recessed floyd cavity and lower horn scoop, but also has beveled scoops on both upper and lower horns on the rear side, similar to a Proaxe body. I’m not sure how it ended up this way - my speculation is that this is the final evolution of Kramer bodies, but based on the serial number this was one of the last ones out the door before bankruptcy so there is not a lot of information about.

This guitar was always very brittle sounding, so I removed the JB A2 and put in a PATB-1 Parallel Axis. I thought it would be funny to put the PATB into a guitar with the slanted humbucker mount, and it does sound great. I also wired up a tiny tone pot which sits fully open inside the control cavity to help tame some of the highs associated with having only a single volume knob.

The trans red pacer previously had the “claw” neck, which I moved to the FF Red sustainer body in the center. The action on the FF Red sustainer is as perfect as I’ve ever seen, really a fantastic player. This has a TB-4 JBJ that I removed from a ‘94 or so ESP Mirage, and the neck is a regular SH-4 JBJ, set much lower to keep the volume in check. This is a surprisingly great combination, and the JB is really fun in the neck position. The body was NOS, so it did not have holes drilled for pickup rings - so I mounted them directly to the wood since this would be the only opportunity to do so on a body like this. For now, there are only volume/tone and a selector, but I plan on wiring up some type of electronics to make use of the extra holes drilled in the body.

The white Sustainer finally has a neck pickup, a Dimarzio PAF Pro which I really enjoy - I think I’m growing to be a big fan of high output neck pickups. The Dirty Fingers in the bridge sounds awesome as always, but to occupy the extra holes in the body, I’ve installed a wah/midboost circuit from GuitarFetish. When it is turned off, I have access to volume, tone, a 3-way selector, and a 3-way coil tap switch towards the neck. The next switch is a two-way, which turns off or on the circuit, and the last switch changes the mode of the circuit, either Wah or Mid-boost. The third knob controls the active electronics - for example, I can preset a cocked wah sound with that knob, leave the effect off while playing rhythm, then flip it on with just the toggle for an instant solo tone, especially useful when covering songs with synth lead parts. Alternatively, I can set a boost amount, then flip on the mid boost with the switch for more gain. It’s a lot of fun, and I may use the same electronics on the FF Red project as well.

New Amp: ADA MP-2

I’ve had a lot of fond memories with my ADA MP-1, a few times while moving around it was my only amp and it pulled double duty as a practice amp, a microphone preamp, even a headphone amp run through my PC with an IR back in the early days of IR’s just to have something to practice on.

I knew that an MP-2 existed, although it isn’t as highly regarded as the MP-1, so I’ve always wanted one to find out for myself.

Well, I’ve finally gotten one - and I also picked up a 6-slot rack and someday I hope to fill all six slots with various rack preamps - Peavey Rockmaster, ENGL E530, Marshall JMP-1… all on my list to grab someday (I run these through the FX loop in of my Marshalls instead of through a rack poweramp, which is fine for my setup).

I think this is an extremely underrated amp and it is entirely held back by one thing alone - how complicated it is to set up. Most guitar players just want to turn a few knobs and start playing, and even on the MP-1, you basically chose either distortion or clean and a few EQ settings and started playing. On this amp, it’s not that simple - there are 10 different preamp voicings, and each has the usual ADA setup with two gains, a 4-band EQ section (there is a presence control but this is a preamp so it’s more like “very high treble”). That alone isn’t too bad, but some of the voicings are a little less interesting sounding because clearly this amp was intended by the designers for you to use the second part too - all of the effects. This amp has a noise gate, graphic EQ, and several effects including the classic chorus that ADA’s are famous for. The problem is that the amp relies on these to get the optimal tone - as opposed to the MP-1 which is a bit more plug and play, although that one also benefits nicely from further processing - how many MP-1 players say they don’t like the MP-2, but then use a BBE Sonic Maximizer and a rack mount Graphic/Parametric EQ in the chain anyway. It’s just a different way of doing it with the MP2 because it’s all self contained.

All of that said, I still think the MP-1 is superior in tone because I like the voicings better, but I’ve also had the MP-1 for a decade and I’m still new to the MP-2, so that’s probably a big part of it. Someone wrote a computer program to configure the MP-2, if I can get that working I think that will be a huge improvement for me if I can set up some patches in advance and then just download them to the MP-2 instead of having to program on the MP-2 itself. Either way, I think with the same 128 stored presets, and now so many voicing, effect, and EQ options, I would love the MP-2 as a touring musician if I played the same material constantly. I feel like I could program in 2-3 patches for every song in the set and still have space left over.

I’m glad to have this one in the arsenal, but it’s going to take some time to get the best out of for sure.

Kramer guitar project

I’ve wanted a maple fretboard Kramer for a long time, but they are few and far between in the “pointy” era (86-90). After I happened across a nice sustainer body on reverb for too low of a price to pass up, I had visions of a chance to do a graphic finish and a maple board.

IMG_5693.JPG

I lucked out and snagged a fairly beaten maple neck from Craigslist (thanks Joe!). Someone had tried to lacquer the neck and didn’t do the best job, but structurally it is in perfect shape. I personally like lacquered necks as opposed to satin or oil finishes, but this one looks to be lightly brushed on and has a few bumps along the back. I think when I have the time, I’ll do some sanding and apply some more lacquer to smooth it out, then it will be perfect.

IMG_5694.JPG

Since I don’t have the sustainer circuitry, I picked up a GFS Modboard that’s a switchable wah or midboost. I haven’t heard it yet, but with so many free holes for switches I wanted to put something in. I’m hoping I can get a similar sound to my Charvel Spectrum’s JE-1500.

At the moment, the bridge pickup is a Gibson Dirty Fingers, which I’ve never had before - and it sounds fantastic. My neck pickup is eventually going to be a Dimarzio PAF Pro, but the one I bought used has larger holes than I have screws for right now so I just left it empty for now. 

IMG_5695.JPG

Stay tuned as I add the rest of the parts and get to work on the finish. Really excited about how this is going to turn out!

New Amp: Mesa Mark IV

A while back, I listed my Marshall TSL for sale online. At the time, I was enjoying the 6100LM more and figured it made sense to sell it off if I wasn’t using it. Thanks to a number of interested and chatty folks I met on Reverb, I learned some new settings and grew to love the amp again, so I took the sale down. However, one person was interested in a trade for a Mark IV combo amp - which didn’t go through as he was able to sell it for cash first. While researching the trade, I started to really like the Mark IV tones and thought it would be great to have especially since it would be so different from my mostly Marshall-like collection so far.

Fast forward a few months and I found a Mark IV Medium head for a really great deal and picked it up. I specifically wanted the Medium head so that the “lead voicing” switch was on the front panel. I’m really a tweaker at heart and though I would use that switch with enough frequency plus the medium head is a better platform in case I had to place another head on top.

NFX_9296.jpg

This is a killer amp - the high gain tones are super tight and articulate, and even sounds great boosted. Throwing a light chorus and reverb in the loop can get tones very close to Whitesnake’s 1987 album tones (even though they used a Mark III), and of course it can nail those modern metal tones such as Lamb of God.

Dialing this amp is a steep learning curve, and I understand now why players come back with such conflicting reviews on the Mark series amps. Their EQ is situated much earlier in the circuit, right after the input gain stage. This is very different to the usual Marshall style post-EQ that most high gain amps employ. On the Mark, you really need to bring up the treble control to maximum, keep the bass low to avoid flubbiness, and use the graphic EQ to shape the sound you want in the room. The idea of maxing out the treble control on a Marshall style amp is totally alien, but it sounds fantastic with this style of circuit.

Caps in this unit date to 1997, and it came equipped with 2x 6L6GC and 2x EL34’s, which sound great to me.

More Details Here

New Amp: Marshall 6100LM... again

I was so thrilled with my 6100LM that I spotted another one for a very low price on Guitar Center’s used lisings, so I pulled the trigger. I figured I could keep whichever one I liked better and sell the other and pocket a few bucks along the way. This unit dates from 1995 and has the same 5881 power tubes as my 1997 model.

Turns out, this one has been modified - and poorly. Channel 1 and 2 feel about the same, but channel 3, the most exciting part of the 6100LM to me, has far less gain and less fullness. Looking inside, there is some shoddy soldering on the lead PCB and I didn’t take the time to investigate further as I’m able to return this amp for 45 days no questions asked.

IMG_5324.JPG

New Amp: Marshall 6100LM

Finally added another Marshall to the collection! This time another 3 channel one, and from around the same era as my TSL. This one dates from 1997, very late in the production run of these 6100LM’s and is equipped with 5881 power tubes.

I’m very happy with this amp and it barely steps on the toes of my TSL. It does cover some of the same ground, but the tones of this model are definitely more classic sounding than the TSL, especially the crunch channel, though it sadly lacks the TSL’s great spring reverb.

The most exciting part of this amp for me is the “LM” lead channel - I thought the TSL had a good amount of gain but really felt best boosted with the gain rolled down. This 6100LM needs no boost to achieve the same level of gain - especially with the mid boost switch pressed in. Channel 2 is also capable of a similarly massive amount of gain with both switches in (Mode C), though it lacks the mid boost ability. Also usable on channel 3 is a “contour” switch, which shifts the mid frequencies and scoops some of it out. While I don’t usually use the contour switch, my first impression is that with that switch in and the gain turned up can get very brown sounding, and could probably do a great impression of the Unchained riff.

IMG_5258.JPG

New Guitar: Charvel Model 4 Cobalt Blue

I grabbed this one online from Guitar Center’s used section, and it did not come with the pictured case - sadly it was very poorly packed, basically the guitar in a cardboard box with no bubble wrap or any protection whatsoever. When it arrived, the edge of the body where your elbow would was cracked through the finish and causing the thick paint to life off in a big chunk. The bridge had also slipped off its studs, but luckily the knife edges didn’t take too much damage. So, another great guitar marred by yet another terrible GC packing job - I can’t even blame UPS for this one as there’s not much they could’ve done. In fact, I’d have to commend UPS for not breaking the headstock or even chipping it - besides the damage from the body moving side to side, once I repaired the bridge and cleaned it up, there were no other issues to speak of and I was able to start playing immediately. For the time being, I’ll put a tiny line of clear nail polish over the edge of the paint so it doesn’t lift any further but I’ll have to contact GC and see if they can cover some of the repair cost… or perhaps this one will get returned, at this price.

Sour notes about shipping aside, this is a beautiful deep blue color and has the same features as my grey Model 4 I picked up last year. The JT-6 trem and JE-1200 mid boost circuit offer great tones, and I really love the inlays on this neck. There’s something special about this neck, it’s just really well put together and a great player.

New Amp: VHT Pittbull 50/CL

I picked this up really on a whim. Usually I research for months/hours of clips, forums, reviews etc, but I only knew that this was a popular amp for metal styles and a few minutes I spent playing a VHT Pittbull 50/ST in a guitar center about 5 years ago.

Well I am sure glad I did, because this is a fantastic amplifier. Somewhat unique to Pittbulls, this one is optioned with tube powered spring reverb, and no graphic EQ. I’m sure the graphic EQ is great to have, but I love the ambience the reverb adds with its relatively short tail, and I can always add an EQ to the FX loop later. Also a very cool feature is the switchable 5U4 tube rectifier, which can be set to both channels, or none, or only on Red but not Green (my preferred setting).

Both channels can be set exactly the same, which I really like as I can dial in two high gain tones, or two crunch tones, or clean/high gain or anything in between.

ezgif-6-0e32dd38cf49.jpg